HEXIS BODYFENCEX Gloss Paint Protection Film

BODYFENCEX is a transparent adhesive-coated film, which is self-healing at ambient temperature and specially developed for protecting car bodywork. Its excellent shock-absorbing properties protect your bodywork against chips caused by stones, insects, car doors, washing brushes, etc. Glossy surface finish.

Average values unless noted otherwise.

Silicone-coated PET liner.

Measured average values at publication of the technical data sheet.

• Solvent-based acrylic adhesive.
• Immediate and permanent adhesion, optimal after 24 hours of contact.

• Wet application method.
• Recommended minimum application temperature: +10 °C (+50 °F). Apply preferably between +15 °C and +35 °C (+59 °F and +95 °F).
• Operating temperature range: -40 °C to +90 °C (-40 °F to +194 °F).
• The BODYFENCEX film is intended for vehicle body protection. It can also serve as a protection system for full wrap films (HX20000, non-structured HX30000 and HX30SCH00) that are used for smooth and basic full wraps without relief decoration. The application of BODYFENCEX to full wrap films is at the customer’s judgement. HEXIS recommend the use of pre-cut BODYFENCEX for this particular application. As the adhesion of BODYFENCEX is permanent, its removal from a full wrap film can damage the latter. HEXIS decline any responsibility in the case of deterioration of a full wrap film caused by the application and removal of BODYFENCEX.
• Self-healing properties of the film at ambient temperatures: this phenomenon of reabsorbing scratches accelerates especially as the temperature increases.
• Cut the film to the size of the part to be wrapped, allowing +10 cm (4 in.) of extra margin.
• Apply to a surface that is clean and free from any traces of contaminants (dust, grease, wax, silicone, etc.). Particular care must be taken to clean the angles and periphery of the target surfaces in order to enable the film to adhere properly to the surface.
• In the case of an already painted substrate, self-adhesive media must only be applied to undamaged original paintwork. If the paintwork is not original and/or damaged, the application and the removal are at the judgement and risk of the installer.

Operating Recommendations

• Conformable product developed for protecting bodywork, underbody, painted bumpers and rear-view mirror casings against chips caused by stones, insects and scratches.
• Excellent protection against vandalism (key scratches).
• To facilitate application, HEXIS have several types of squeegees in their range of accessories, ranging from softer to harder (plastic or felt).
• For more information on the application method of the BODYFENCEX film, please refer to its Application Guide available under the “Professionals” heading, in the “Solar and safety films” category on our website www.hexis-graphics.com.

• Vertical exposure: up to 10 years (under normal road use conditions).

Applied to a full wrap film with a durability of less than 10 years, BODYFENCEX will increase the durability against yellowing and cracking of the full wrap film by up to 1 year (within the limit of the BODYFENCEX durability).

Lifespan depends on the type of substrate, substrate preparation, exposure conditions and nature and frequency of the cleaning. For instance, it is estimated that a south-facing exposure will divide the durability by two. The same applies to a horizontal exposure. In addition, elevated temperatures (above +50 °C) (+122 °F) or pollution significantly reduce this durability.

To find the indicative durabilities of the films for any other exposure and geographical area, please refer to the “Conversion rules for indicative durabilities according to geographical area” chart available under Durability, on the “Professionals” pages on our site www.hexis-graphics.com.

Due to the great variety of substrates and the growing number of new applications, the installer must check the suitability of the medium for each application. In case of doubt, request an expert evaluation of the compatibility of the film and the glass in question. All of the published information is based on measurements regularly performed in the laboratory.

• This warranty applies to any individual purchaser’s personal vehicle on which a protective film of the BODYFENCE range is installed.
• To be valid, the warranty requires that the purchasers register the vehicle online on the dedicated website, within 30 days following the product purchase date.
• They must specify the purchase date of the protection film of the BODYFENCE range, the name of the installer, the invoice number of the installation, and the chassis number of the vehicle.
• The film must be installed by a professional (an installation that has been performed by a BODYFENCE certified installer increases the duration of this warranty). Any installation carried out by a private individual will not be covered by this warranty.
• The installation must be performed on the original paint and the purchaser must follow the maintenance requirements for the BODYFENCE protection films given in our application guides available on our website www.hexis-graphics.com.
• This warranty is not transferable. Warranty coverage is only applicable to the original purchaser of the product. This warranty coverage definitely ends in case of selling or processing of the vehicle.

HEXIS S.A.S. warrant their BODYFENCE range films (upon reference) for a duration of 7 years up to a lifetime warranty. The warranty period varies according to the film and according to the HEXIS certification or non-certification of the installer.

Scoped to the films this product belongs to; the Warranty document covers other BODYFENCE-range films under a different row of the same table, not reproduced here.

These warranty durations are valid regardless of the product exposure (both vertical and horizontal).

• This warranty covers the following faults: yellowing and cracking of the product due to imperfections in material or manufacture.
• The warranty applies exclusively to films installed on automotive vehicles used on roads suitable for public traffic.
• If the product is found to be faulty, HEXIS commit themselves to replace the respective product free of charge.
• The product will be, at the discretion of the purchaser, delivered, either to the purchaser or to an installer whose contact address will be communicated to us.

The blemishes of the installed film are not taken into account in this warranty. Only the installer of a protective film of the BODYFENCE range is responsible for the aspect of the product once installed.

If, before installation, the professional notes a visual fault in the film or adhesive, it is his responsibility not to install it. The installation by a private individual is excluded from this warranty.

Within the scope of this warranty, HEXIS do not warrant the following parameters:

• the film installation or removal duration;
• the substrate and the possible damages which it could have undergone;
• the substrate recovery;
• any lifting of the film occurred within the 14 days following the installation, due to vehicle cleaning carried out with any kind of detergent;
• scratches and all type of damages caused to the film after having been cleaned in a car wash.

HEXIS commit themselves to replace the products that they accept as being faulty.

The HEXIS BODYFENCE warranty applies to the BODYFENCE range films that have been installed by professionals. In no case, this warranty can apply to an installation carried out by a private individual.

The film must imperatively be cleaned with BODYRELOAD and BODYFINISH maintenance products, at least every four months, following the instructions described in the latest version of our application guides available on our website www.hexis-graphics.com.

Climatic effect: the degradation of materials is a natural and unavoidable phenomenon. A slight and progressive modification of the transparency, colour and gloss, as well as a slight peeling off at the edges and around the rivets are normal phenomena that do not fall within the scope of this warranty.

A usage of our products that is not in accordance with the indications defined in the technical data sheets and application guides, involves the responsibility of the installer for any risk arising from this usage or application. In the case of usage that is not in accordance with the specifications in the technical data sheets, application guides and maintenance requirements, it is the responsibility of the installer to determine the compatibility between the HEXIS product and the application, and the risks and/or obligations related with this installation. In no case, the end user can address to HEXIS, under no circumstances, a claim or compensation request within the scope of this warranty program.

• Adhesive tape Tesa® 50110
• 1-litre PULVERISAT vaporiser
• 19-litre SHAGSPRAY vaporiser
• HEXISOAP application solution to be diluted
• STEAMERSC3 steam cleaner
• HEXISGEL application liquid
• Demineralised water
• SHAGFENCEM or SHAGPAM squeegee
• CUTOLFA30 30° blade cutter
• LAMOLFA30 refill
• Liquids for the cleaning of application surfaces:
  • SHAGREMOV
  • SHAGCLEAN
• ProTech® SHAMPCARV2 car shampoo
• Soft cloth
• BODYFINISH cleaning kit
• CERAMIC COATING KIT NANOSERUM BY HEXIS

The Bodyfence films are specially developed for protecting car bodywork. Its excellent shock-absorbing properties protect your bodywork against chips caused by stones, insects, car doors, washing brushes, etc. They also provide an excellent protection against vandalism.

BODYFENCE: BODYFENCE is a transparent adhesive-coated film with improved surface sliding in comparison with PVC films (CAR100B).

BODYFENCEX: This transparent film is self-healing at ambient temperature. Its wider version, called BFWIDE, is specially developed for protecting large-sized car bonnets. DFENCEXTRM is thicker and specially developed for protecting the front side of vehicles. In comparison, the DFENCEONEX film is thinner and particularly suitable for protecting a car’s interior surfaces (excluding textiles and surfaces incompatible with wet application).

BODYXFAST: The transparent, ultra-flexible product is self-healing at ambient temperature and specially developed for quicker and easier film application.

BFBLACK: This black film is self-healing at ambient temperature.

They are available in glossy, matt or satin surface finish, upon product code.

Application methods are based upon HEXIS’ experience and are non-restrictive. Comply with instructions to ease application of HEXIS films. The illustrations in this document are representative and not binding; the accessories and products used may differ depending on technical and commercial developments. HEXIS also offer training sessions for beginners and professionals to achieve optimum results.

Your BODYFENCE film can be applied to any vehicle body as long as the target surface is clean, smooth, non-porous and free from any traces of oil, grease, wax, silicone or other contaminants. To avoid unexpected outcomes, always assume that every substrate is dirty and needs to be cleaned.

It is recommended to carry out a preliminary trial on a small, inconspicuous surface area of the substrate to check the compatibility between the different elements.

For further technical information on the BODYFENCE film, please refer to the technical data sheet available on our website at www.hexis-graphics.com.

Keep the films away from any major source of heat (radiators and heaters, direct exposure to sunlight, etc.): the best temperature ranges from 15 °C to 25 °C (59 °F to 77 °F) with relative humidity of 50 %.

Store your films in their original packaging, in a dry environment. The rolls are wrapped in sealed polyethylene bags and are maintained in their cardboard packaging by plastic suspension caps to prevent the windings from being crushed by their own weight.

Always store the rolls in an upright position.

• Optimal adherence of the BODYFENCE films is obtained after 24 hours following application.
• The BODYFENCE films are usually used on the vehicle body areas the most exposed to aggression (bumper, bonnet, doors, etc.), however, they may also be used on the entire car surface!
• After cutting the necessary film length for the wrapping project, the remaining film must be stored on its original core (do not cut the rolls into several lengths, do not repackage the product); the roll must be closed immediately and properly after use (tape or roll-collars), without exerting pressure on the film, in order to preserve all its qualities.

Before proceeding with any application, the installer must first inspect the substrate and the paint to which the film will be applied.

The installer and the client are responsible for the suitability assessment of the target surface to be covered.

2.1. Preliminary inspection of the substrate

• Any fresh new paint must have dried for at least 7 days at 25 °C (77 °F) to outgas completely. An outgassing test must be carried out before applying the film.
• Any old, powdery or flaky paint must be sanded and renewed before application and must undergo a tear-off test.

2.2. Tear-off test

Using a TESA® 50110 adhesive tape, or similar, apply it to a surface of 2.5 cm x 5 cm (1 in. x 2 in.) plus some overhang material for easier removal. Fold and tear it off with one quick pull perpendicular to the substrate surface. The film must generate a certain resistance during its removal. Repeat this process in several places.

On request, HEXIS can provide you with a Tesa® adhesive tape in 2.5 cm x 5 cm (1 in. x 2 in.) size. HEXIS cannot be held liable for any damage to the substrate following the execution of this test.

2.3. Outgassing test

Use a square piece of around 15 cm x 15 cm (6 in. x 6 in.) of self-adhesive polyester or of the film to be applied. Wait for 24 hours or 2 hours at 65 °C (149 °F). The appearance of bubbles indicates that the substrate has insufficiently outgassed. Therefore, this process should be repeated after a couple of days; or else the procedure described below should be carried out.

2.4. Outgassing procedure with flame treatment

(Polycarbonate, translucent or diffusing methacrylate, expanded PVC, etc.)

This method consists of changing the surface tension of a substrate by swiping it with the flame of a gas burner. Using the flame’s blue tip, proceed evenly with fast sweeps horizontally and vertically along the whole substrate surface.

MOVE THE FLAME IN SWIPING MOTIONS ON THE SUBSTRATE (RISK OF DESTROYING THE SUBSTRATE IF A FIXED POINT IS HEATED MORE THAN A SECOND).

The film must be applied right after that treatment as this light surface treatment disappears after a few minutes.

HEXIS are not liable for any bubbles caused by outgassing.

Cleaning of the substrate is required before performing the application. It should always be assumed that the substrate is contaminated with dirt. Some residues or contaminants may not be visible; however, they may impact the adherence of the film.

Before using any cleaning liquids or chemicals, please refer to the technical data sheets and safety data sheets available for download on our website at www.hexis-graphics.com.

3.1. Clean and soiled surface appearance

For vehicle wraps, it is advised to wash the vehicle with the SHAMPCARV2 vehicle body shampoo, then carry out a final cleaning using the SHAGCLEAN product.

3.2. Heavily soiled surface appearance

For vehicle wraps, it is advised to wash the vehicle with the SHAMPCARV2 vehicle body shampoo, then use the SHAGREMOV product.

Handle the SHAGREMOV product in a ventilated area. Wear protective goggles and gloves. Prior to treatment, run a compatibility test on a small, inconspicuous area of the substrate to be treated. Indeed, certain plastic materials might be damaged by the SHAGREMOV product.

• Spray the SHAGREMOV product onto the dirty surface and spread out using a dry cloth.
• Then wait for a few minutes. Spray the SHAGREMOV product again, then wipe it dry with a clean cloth or squeegee.
• When the substrate is clean and dry, carry out a final cleaning using the SHAGCLEAN products.

The recommended minimum application temperature is +10 °C (+50 °F). Preferably, apply at a temperature ranging from +15 °C to +35 °C (from +59 °F to +95 °F).

The film must be applied using the ‘wet’ application method, either with the diluted HEXISOAP application solution or with our ready-to-use HEXISGEL product (for strongly deformed surfaces).

• To apply with the HEXISOAP application solution, prepare the PULVERISAT or SHAGSPRAY vaporiser with water, supplemented with 1 pump of HEXISOAP per litre of water. This mixture can be easily removed with the squeegee during installation.
• Measure the parts to be covered. Cut the BODYFENCE while leaving a margin of at least 10 cm (4 in.) around the surface to be covered in order to stretch it during application, and avoid any finger marks. (FIG. 01)
• Carefully separate the liner from the BODYFENCE. (FIG. 02)
• Spray the diluted HEXISOAP application solution or HEXISGEL on the part of the bodywork to be wrapped and on the adhesive-coated side of the BODYFENCE film (FIG. 03). This will enable a better positioning of the product on the vehicle.
• Firmly stretch the BODYFENCE and position it (adhesive-coated side on the body) in order to wrap the structure. (FIG. 04)
  • Note: For an optimal wrapping of a concave or convex surface, it may be necessary to soften the film using the STEAMERSC3 steam cleaner.
• Apply the film using one of the SHAGPAM or SHAGFENCEM squeegees, according to the size and the deformation level of the surface to be covered.
• For a better gliding of the squeegee, spray the diluted HEXISOAP application solution or HEXISGEL, depending on the level of deformation, on the BODYFENCE film. Then apply the film with the squeegee, while holding it at an angle of 45°. Press firmly to adhere the film to the surface and remove the application liquid. (FIG. 05)
• After all removal of the BODYFENCE for adjusting or positioning, spray the film and vehicle body before any reapplication.
• Considering the different existing paint qualities, it may be necessary to activate the adhesive strength by spraying the very concave and/or convex shapes with HEXISGEL.
• Once the BODYFENCE film is applied, cut as indicated in the following paragraphs.

4.1. Straight cut with overlap

To avoid scratching the paint, the cutter blade must always be parallel to the vehicle body.

• Use a cutter with a new blade.
• For carrying out the cutting, the cutter blade must be placed against the edge of the adjacent section. During cutting, make sure you always follow this edge by positioning the cutter towards the outside. (FIG. 06)
• After cutting, 2 to 3 mm (1 to 1½ in.) of the film should overlap the edge of the covered vehicle body.
• If there are no adjoining sections, cut the film surplus leaving a 2- to 3-mm (1- to 1½-in.) film overlap. (FIG. 07)
• Remove any excess film.
• To finish, run the squeegee over the cut. Incline the squeegee towards the thinner edge (FIG. 08). Firmly apply over the edges, round parts and neighbouring or opposed areas.
• Always cut the angles of the BODYFENCE film in rounded sections in order to ensure optimum adhesion of the cut film edges.

4.2. Cut without overlap

This method is used for a cut along a seal or any trim that cannot be disassembled.

• Use a cutter with a new blade.
• Trace with your finger the contours of the area. Lift the vinyl of the adjacent part and drag it into the hollow using a squeegee so as to mark the seal edge.
• For cutting, the cutter blade must be placed in flat position on the squeegee.
• The squeegee + cutter blade must be parallel to the body and perpendicular to the seal.
• Make the squeegee/cutter blade compound slide over the body to carry out the cutting by always maintaining this blade orientation.
• Remove any excess vinyl.
• Cut the angles of the BODYFENCE film in rounded sections in order to ensure optimum adhesion of the cut film edges.
• Finish off by firmly running the squeegee over the cut.

4.3. Finishing

If the film has been applied on a heavily deformed surface with a liquid other than HEXISGEL, the film edges should be rinsed with demineralised water (or tap water if demineralised water is not available) in order to increase the adhesive’s adhesion to the substrate more quickly.

• Place absorbent paper on the SHAGFENCEM or SHAGPAM squeegee. Apply pressure to the cut edges to remove as much as humidity as possible. (FIG. 09)
• Firmly apply the film with the squeegee to the edges, rounded sections and adjacent or opposite faces of the body. (FIG. 10)
• If wrinkles appear at the edge trim, press them with your finger for approximately 30 seconds. (FIG. 11)

In order to keep your full wrap films clean for longer and make them easier to clean, HEXIS recommend treating them with the NANO SERUM by HEXIS as soon as you have finished the film application and then periodically. This surface treatment increases the hydrophobic protection of the film, it improves its non-stick effect against aqueous compounds and external contaminants, and durably maintains the aesthetic appearance of the BODYFENCE films.

The NANO SERUM by HEXIS must be applied by a qualified professional in a clean, dust-free, well-ventilated place away from sunlight.

HEXIS tip: Please refer to the technical data sheet of the NANO SERUM by HEXIS for the details of the liquid’s application method.

Note: A slight change in the appearance of the film may be observed after treatment with the NANO SERUM by HEXIS, but this will not impair in any way the quality of the film. HEXIS consider this change in appearance to be normal, taking into account the addition of a NANO SERUM by HEXIS layer to the surface of the film, and will not accept any claim on this ground.

The protection of the NANO SERUM by HEXIS is effective up to 36 months, depending on the vehicle’s exposure and maintenance conditions.

The protective effect of the NANO SERUM by HEXIS may be impaired and reduced if the vehicle is frequently cleaned with automatic rollers in car wash stations. The ceramic treatment loses its effectiveness when the water-repellent effect becomes irregular on the surface of the film.

The NANO SERUM by HEXIS is a technical product that requires a meticulous application by a qualified professional. HEXIS cannot be held responsible for any traces of application, demarcations, rings, etc. visible on the film resulting from incorrect application of the product.

HEXIS decline all responsibility in the case of inappropriate use or failure to comply with the safety instructions for all their products.

For optimum maintenance of the BODYFENCE film, HEXIS suggest to use their range of HEXIS cleaning agents included in the BODYFINISH kit, specially designed for total wraps.

The BODYFENCE film can be cleaned in any conventional automatic car wash, using cleaning products and detergents used for professional maintenance of vehicles and advertising equipment.

Nevertheless, for the use of high-pressure cleaners, respect the following procedure: apply medium water pressure at a minimum distance of 50 cm (20 in.) and a maximum water temperature of 35 °C (95 °F).

Caution: However, the film should not be cleaned within the first 48 hours following its application as this can affect the adhesive strength that may result in the film peeling off.

Caution: Solvents and corrosive detergents must not be used.

HEXIS are not liable for any adhesive films cleaned with the unspecified additives from cleaning stations.

Car washes: The additive products and the condition of the rotating brushes may impair the adhesive strength of the films. It is commonly admitted that after 10 car washes, the polyurethane paint becomes streaked; therefore, and in the same way, we are not accountable for these mechanical effects that may affect the film appearance.

HEXIS tip: Always carry out a test on a small area before cleaning the entire surface to be covered.

The BODYFENCE film features a special adhesive designed to facilitate removal.

• Gently lift the corner of the film with the cutter without damaging the substrate.
• Subsequently proceed, by heating small areas, to peel off the film gently.
• The film should form an angle of 70° to 80° relative to the substrate surface to reduce the risk of leaving any adhesive on the substrate or tearing off the film.

An angle more or less wide or acute will cause the film to break more easily.

• Continue to peel off the film gently until it is completely removed while keeping a watchful eye on the heat applied, on the pulling angle of the film, and the pulling speed.
• If any adhesive remains on the substrate, take a cloth soaked with our SHAGREMOV product and rub the surface until all traces disappear.

Prior to treatment, run a compatibility test on a small, inconspicuous area of the substrate to be treated. Indeed, certain plastic materials might be damaged by the SHAGREMOV product. HEXIS are not liable for damages and degradations caused to the substrate by using incompatible products.

Before using any of our liquids, please refer to the technical data sheets available on our website at www.hexis-graphics.com.

For further technical information, please refer to the Technical Data Sheets available for free download from our website www.hexis-graphics.com, on the “Professionals” pages.

Due to the great variety of substrates and the growing number of new applications, the installer must check the suitability of the media for each application. All the published information does not however constitute a binding guarantee. The seller cannot be held liable for indirectly related damages and assumes no liability for claims that are higher than the replacement value of the purchased product. All specifications are subject to potential changes without prior notice. Our specifications are automatically updated on our website www.hexis-graphics.com.